正品 手表专用MTG-1000多功能机械校表仪打线机手表测试仪全自动

MTG-1000型校表仪,有  中文   英文  可选，体积小,适合携带,家庭,工厂经适用/钟表维修/

维时机械表测试仪NO.1000使用说明        

THe WeiShi WATCH  EXPERT  NO.1000 User Manual        Table fo Contents

3

6

 Beat Numbers (Frequency Numbers)

6

8.故障的处理(Common faults and handling)

8.1 After insert the socket,The screen is dark

8.2The instrument can enter testing state wish the sound of "DI",But after placed the watch on the sensor,The instrument do not work

8.3Signal LED is bright,But the lines is scattered or occur many lines

1.仪器性能(Instrument function）

维时机械表测试仪No.1000是一款让手表制造商及钟表维修技师从多方面测试机械表的精密检测仪器。

The WEI SHI WATCH EXPERT No.1000 is a precise mechanical watches test instrument,it is used for multi-testing by watch manufacturers and watch technician.

液晶屏上可将手表频率图完整地显示出来。

The frequency diagram of the watch can be displayed in the LCD screen.

在测试过程中仪器可根据不同的手表自动调整最佳的信号强度

According to different watches,the instrument will automatically adjust optimal signal level during testing.

可自动计算日差、摆幅及偏振的数值并实时显示数据。

The instrument will automatically calculate the rate, amplitude, beat error, and display them by data in real time.

常规节拍的手表仪器可自动感应，对特殊节拍的手表可以手动选择。

For the conventional beat, the instrument can automatically response; for the special beat, can manually select.

可选择2秒、4秒、6秒、8秒、10秒、20秒、30秒、60秒的检测周期并计算出所选时间段手表走时的平均值。

The sampling period can selected by 2 seconds, 4 seconds, 6 seconds, 8 seconds, 10 seconds, 20 seconds, 30 seconds, 60 seconds, and the average of corresponding period will be regard as the precise value of the watch.

可调整6种测试方位，测试中模拟声响可选择有或无。

Six kinds of testing position can be adjusted, and the simulation sound can be play in the speaker or mute.

1. Keys and Display)
2. (Key Function)

A 开始/暂停按键  停止/开始检测手表

A Start/Pause Key    pause /Watch test start

B 菜单/声响按键 

选择要调整的项目及开或关扬声器

 Menu/Speaker Key

Selection of adjustment item or turn on/off speaker

C 数值↓按键

选择下一个更低参数或在仪器测试中调整显示屏的对比度

C Value↓Key

Selection of the next lowerparametersor adjustment of dips’ contrast

D 数值↑按键 

选择上一个更高参数或在仪器测试中调整显示屏对比度

D Value↑Key

Selection of the next higher value or adjustment of dips’ contrast

• (Parameters and Display)

A 日差(快慢) 日差值以秒/天显示

A RATE    Rate deviation in seconds per day.

B  摆幅度   显示摆幅的度数

B AMPLITUDE    Display of the amplitude in degrees.

C  偏振(频率的错误)  偏振值以毫秒显示

C BEAT ERROR       Display of the beat error in ms

D  参数     显示节拍、升角（测试中节拍和升角每5秒切换显示一次）

D   PATAMENTS    Display of the lift angle or the beat (switching by 5s)

A 频率校准口(我公司的工程师才可以校准)

A Frequency calibration Connector(Only the company's engineers can calibrate the frequency)

B 感应器连接口

B Sensor Connector

C 电源连接口

C Power Switch

• .安装(Installation)
• 3(The Basic Equipment Components)

测试仪器主机   Testing equipment host

感应器Microphone

电源器Power cable

产品说明书Instruction

• (EquipmentInstallation)

仪器不能安装在阳光直射或温度超出60℃的地方.感应器应与嘈杂的机械声、喇叭声、尖脆的物品敲打声、超声波清机声保持足够的距离，嘈杂的声音会影响信号的感应。

The instrument is to be installed in such a way that it is not exposed to direct sunlight or to extreme temperature of60℃.The microphone should be placed at a sufficient distance from noisy machines, loudspeakers, sharp stroke sound and particularly from ultrasonic cleaning machines. The high noise will disturb signal sensing by the microphone .

将电源器插入适合的电源插座。电源的电压范围是100V—240V之间。

Insert Power Cable into the mach outlet. Power supply voltage is between the 100 V～240V.

把感应器插头连接到主机的感应器接口处。

The sensor plugs to connect to the host interface Department of sensors.

4.

电源和感应器连接好后，仪器进入测试状态；把手表放在感应器上，手表的把的（龙头）应靠在金属片上。测试方位可随意转换，转换后手应离开感应器及手表，绿色信号灯闪动则已接收到手表的信号。

After connecting of the power and the sensor, the instrument will be testing status.Place the watch on the signal sensor and the uplift of watch (leader) should the sheet metal. Test position can be changed freely; the hand must remove from the sensor after the test position is fixed. Green light flashing, means have received the signal of watch.

1. The Use of Keys)
2. 暂停键(Start/Pause Key)

要调整仪器任何参数时都应先按一次开始/暂停键。

Pleasepress the Start/Pause Key, before adjusting any parameters of the instrument.

先按一次开始/暂停键，仪器停止运行，绿灯熄灭，红灯亮时可以进行参数调整，调整好之后再按一下开始/暂停键，红灯熄灭，绿灯亮，仪器则恢复到正常测试，原有的数据和屏幕显示将重新刷新。

Firstpress the Start/Pause Key one time, the instrument pause. The parameters can be changed when green LED is off and red LED is on. After adjustment rightly, press the Start/Pause Key again when green LED is on and red LED is off. The instrumentwill be carried out the normal test andrefresh the data and the screen to return to running condition.

• 声响键(Menu/Speaker Key)

仪器测试中直按菜单/声响键可开或关声响（扬声器）。

When the instrument running, press directly the Menu/Speaker Key, can turn on or off the speaker.

仪器暂停时，按一次声响/菜单键，进入菜单项，再按声响/菜单键选择菜单，按↑↓键改变所选菜单的参数。

Whenthe instrument pausing, press the Menu/Speaker Key,can enter the Menu window, then press the Menu/Speaker Key, can select the menu item, press the Value Key↑or↓, can change the selected items parameters.

• ↓)

仪器正常测试中按数值↓键可调高显示屏对比度。

Press the Value Key↓candecreasethe LCD’s contrast, when the instrument running.

按菜单键选好任何一种要调整的选项后，按数值↓键则可选择下一个较低的系数值。

Afterpressed the Menu Key to select the adjustment, press the Value Key↓can select thenext lowerparameter.

• ↑)

仪器正常测试中按数值↑键可调低显示屏对比度。

Press the Value Key↑canincreasethe LCD’s contrast, when the instrument running.

按菜单键选好任何一种要调整的选项后，按数值↑键则可选择下一个较高的系数值。

After pressed the Menu Key to select the adjustment, press the Value Key↑can select thenext higherparameter.

• Parameters)

Beat Numbers (Frequency Numbers)

自动Automatic  

仪器自动选择的节拍有：

The following beat numbers are selected by automatic selection mode：12000、14400、18000、19800、21600、25200、28800、36000、43200。

（如果所测手表的节拍不在自动选择范围内，仪器则显示最靠近的节拍数，但测试的结果是错误的，此时应用手动选择节拍功能调节到相对应的节拍）。

(If the tested beat is not in automatically selection, the instrument will display the closest beat number, but the test result is not correct. At this time, use the manual mode to select the relative beat.)

手动选择可以选择出仪器无法自动识别的节拍数目及很少见的节拍数目。

Manual selection can selected out the beat number that Automatic select can not identify and rare beat number.

手动选择的节拍有：The following beat are selected by Manual selection mode：3600、6000、7200、7380、7440、7800、9000、9100、10800、11880、12000、12342、12480、12600、13320、13440、13500、14000、14040、14160、14200、14280、14400、14520、14580、14760、14850、15000、15360、15600、16200、16320、16800、17196、17258、17280、17786、17897、18000、18049、18514、19332、19440、19800、20160、20222、20944、21000、21031、21306、21600、25200、28800、32400、36000、43200。

大多数普通机芯的升角为52°,所以仪器出厂是设置的升角数值为52°。在计算摆幅时需要这个数值，升角可设定为30°至70°之间。

The lift angle is52°for many common movements, therefore the lift angle value of instrument for factory is set to52°.This value is required to calculate the amplitude and must be selected according to the watch movement.The lift angle can be set to between30°and 70°

测量周期有：

The measuring period selectable:2s、4s、8s、10s、20s、30s、60s

用于计算测试结果的平均值。

Use to recalculate the average values of the test result.

测量范围：机械表快慢的日差、摆幅、偏振、线条显示手表走时。

Measuring possibilities: Rate deviation, amplitude, beat error of mechanical watches and diagram recording of the beat noise.

频率数目：可自动选择常见手表的节拍，也可以手动选择不太常见的节拍。

Frequency numbers: It can selected out the common beat number automaticly, also can selected out the less common beat number by manual.

日差测量：以数字显示±999秒/日，测量范围内以1秒/日显示。

Rate deviation measurement: the range of deviation is ± 999 sec / day, precision 1.0 sec/day.

摆幅测量：以数字显示，分率为1°，测量范围100°—360°（升角值会影响摆幅，范围是30°—70°。正常情况下手表的摆幅度不要超过330°）

Amplitude measurement: Numerical display in degrees, resolution is1°,measuring range:100°to360°(the lift angle can affect the amplitude, range:30°to 70°.Under normal circumstances, the amplitude value do not exceed360°.)

测量平均值的时间：2s、4s、8s、12s、20s、30s、60s。

Measuring period times for the average numerical results: 2s, 4s, 8s, 12s, 20s, 30s, 30s, 60s.

偏振（频率错误）测量：数值单位为毫秒；分辨率是0.1毫秒，测量范围是0.0—9.9秒。

Measuring of the Beat error(Frequency error): Numerical display in milliseconds. Resolution is 0.1 milliseconds; the measuring range is 0-9.9 ms.

升角：升角的测量范围是30°—70°，出厂设置为52°。

Lift Angle: the measuring range is 30 ° to 70 °, the factory set it to 52 °.

供电电压：单相交流100V—240V±10％两线。

Supply voltage: single-phase AC 100 V～240V ± 10% two-line.

测量方位：1—6个方位。

Measure positions: 1 to 6 positions.

使用环境：0℃ —50℃，相对湿度：0—80％RH

Use of the environment:0℃to50℃, relative humidity:0 to 80% RH

外壳：浅灰色塑料外壳     Shell: Light grey plastic

尺寸：173×9.5×11.5mm   Dimensions:173×9.5×11.5mm

• 重量：402g               Weight:402g

常见故障的处理(Common faults and handling)

• After insert the socket, the screen is dark. Check the power pilot LED is bright or not.

• 开机后仪器“嘀”声响进入到测试状态，装好感应器并放好手表后，仪器不工作

The instrument can enter testing state with the sound of “Di", but after placed the watch on the sensor, the instrument do not work

.检查手表是否会转动（并且摆幅要100°以上），手表的把头（龙头）是否接触到感应器的金属片上。

Check the second hand whether rotation (and amplitude must be more than 100 °), the crown of watch (leading) is against at the sheet metal of sensor.

Signal LED is bright, but the lines is scattered or occur many lines.

可能是节拍不对，可手动调整符合手表的节拍（频率）。

Maybe the beat is mistake, adjusted the right beat (frequency) by manual selection.

 

 

 欢迎您光临忠诚仪器工量具
 

    公司是实体加网络销售为一体，有正规的普发票与增值税网上发布价格都是不含发票的价格 开客户要求开发票要加税点谢谢合作，公司销售服务各类

牌检测仪器、工量具、自动化设备等、价格优势，公司有专业销售售后服务工程师
，大家选购时可以放心。

公司宗旨：精心合作、质量第一、最真诚的服务、最优惠的价格。

 

欢迎光临：忠诚仪器工量具
联系人：熊喜照  马晓媛
联系电话：13626524408、13757794177 
电话：0577-86833372传真：0577-86833373
诚信通：xiongxizhao1
网址：

 
公司网址：www.jxjm17.com